Standard Parts

           فهرست تصویری قطعات پیش ساخته

 

 

  • Dowel Pin with Internal Extracting Thread D26

    ● DIN EN 28735/ISO 8735-A
    ● Hardness 60±2 HRC

    ...
  • Locset Anaerobic Adhesive-Pipe Sealing

    ● LOCSET Pipe Sealing
    LOCSET Sealing are used in threaded joints and pipes to sealing or eliminate the possibility of leakage.The connection does not open and will not leak due to vibration.the joint is protected from corrosion and retains its properties until opened(with generally tools)

  • Precision Punch D223

    ● DIN 9861
    ● Material :ASP 23 , HWS , HSS
    ● Head hot upset-forged and tempered
    ● In D222,D224 punches residual upset bulge below head normally much smaller than permissible acc. to DIN 9861.
    ● In D223,D225 punches shank and head subsequently precision plunge ground for perfect Concentricity and full interchangeability with replacment punches.

    ...
  • Sliding Pad D063

    ● Non-Liquid Lubricant
    ● Material: Bronze/Cast Iron
    ● Are used in applications of linear or rotary motion in tool making, and similar engineering uses.
    ● Advantages of oilless guide elements:
    - Good emergency sliding properties.
    - Highest carrying capacity at low speed.
    - Useable under water or with chemical solutions.
    - Extremely wide temperature resistance hot and cold.
    - Damping properties in presence of vibration.

  • Light Green Spring D64L

    ● DIN/ISO 10243

  • Modular Retainer(Slide Fixture) D541/8

    ● Material: Steel, Hardened

    ...
  • CIRCULAR Die Set CH

    ● Cast Iron-Center Pillars
    ● DIN 9812 Shape D and DG

    ...
  • Guide Pillar D0131

    ● Material:~1.7131 / 720HV
    ● Similar to DIN 9825 / ISO 9182-2
    ● Easy replacement and disassembly, installation.

  • Guide Pillar D031

    ● Material : ~ 1.7131 | 720HV

    ...
  • All-Steel Die Set 5S...B/T

    ● Plates Material: St37 , St52 , 1.1730
    ● Points:
    - Other plates material, the sizes out of table, guide system, special machining and annealing of plates can be done on request.
    - When the dimensions of the plates are larger than 500mm, the plates are equipped with 2 screw-in lifting studs named E201 in order to have an easy transportation.
    - Regarding the thickness and dimensions of the Plates, more accurate tolerances can be done if requested.
    - Possible to produce and montage your special guide system.
    - Delivery time: 10 to 15 days respectively to dimensions of a1,b1.

  • Pressure Elastomer Spring D63/95

    ● Material : PUR/95 Shore A

  • PULL-DOWN CLAMP E3060

    ● Low Height
    ● Material: Heat-Treated Steel

    ...
  • PLAIN CLAMP E307

    ● Material : Heat-Treated Steel
    ● DIN 6314

    ...
  • SUPPORT E312

    ● Adjustable

    ...
  • T NUT E407

    ● DIN 508
    ● Tensile strength class 10.
    ● Full load capacity is only allowod with the full thread length matched.
    * Use the length of the thread.
    ** Excess of Din508

    ...
  • Guide Bush D11

    ● Material : ~ 1.7131 | 720HV
    ● DIN 16761-E

    ...
  • Ejector Pin-Cylindrical Head D41K

    ● DIN 1530 - ISO 6751
    ● Material: WAS(Hot Working Steel Nitrided)
    ● Plasma - Nitrided Black Oxidized

    ...
  • Locset Anaerobic Adhesive-Surface Sealing

    ● LOCSET Surface Sealing
    LOCSET surface sealing is used for complete sealing of two metal plates and flanges, so that after two plates are stacked, it fills all the scratches and creates the best surface sealing. Excess adhesive remaining in the inner case is not cured and can be removed without disturbing or contaminating it.

  • Locating Ring D100

    ●Material: 1.7131

    ...
  • Sliding Pad D065

    ● Non-Liquid Lubricant
    ● Material: Bronze/Cast Iron
    ● VDI 3357
    ● Are used in applications of linear or rotary motion in tool making, and similar engineering uses.
    ● Advantages of oilless guide elements:
    - Good emergency sliding properties.
    - Highest carrying capacity at low speed.
    - Useable under water or with chemical solutions.
    - Extremely wide temperature resistance hot and cold.
    - Damping properties in presence of vibration.

  • Rectangular Die Set CZ

    ● Cast Iron-Diagonal Pillars
    ● DIN 9819 Shape C and CG
    * Different from DIN 9819

    ...
  • Guide Pillar D011

    ● Material : ~ 1.7131 | 720HV
    ● The main advantages of D011 are easy moving in g6 and pressing fitness of m6 in reamed bore of H7.

    ...
  • Guide Pillar D028

    ● With Collar
    ● Material: Steel, Surface Hardened

    ...
  • All-Steel Die Set 3SH

    ● With Stripper - Plates Material: St37, St52, 1.1730
    ● Similar DIN 9868/ISO 11415

    ● Points:
    - Other plates material, the sizes out of table, guide system, special machining and annealing of plates can be done on request.
    - When the dimensions of the plates are larger than 500mm, the plates are equipped with 2 screw-in lifting studs named E201 . in order to have an easy transportation.
    - Regarding the thickness and dimensions of the Plates, more accurate tolerances can be done if requested.
    - Possible to produce and montage your special guide system.